Mikuni carburettor main jet hexagonal 4/042#Size for Mikuni VM carburettor Mikuni TM carburettor Mikuni TMX carburettor

Mikuni carburettor TM35-1

The carburettors are often used for a conversion of the Yamaha Banshee or RD350.

The offer includes:
2x carburettor TM35-1
(jetting and needle of your choice (standard jetting if not specified))

The offer also includes:
Jetting of your choice (standard jetting if no details are given)
A different nozzle needle (if required) (standard if no details are provided.

Normally, the nozzles and the nozzle needle are replaced. All we need is your setup. Simply contact us or make a note during the ordering process.

Mikuni carburettor TM35-1

The carburettor is also often used for conversion on other mopeds and scooters, such as Vespa, Aprilia RS, Suzuki RGV, Yamaha TZR etc.

The offer includes:
1x carburettor TM35-1

The offer also includes:
Jetting of your choice (standard jetting if not specified)
A different jet needle (if required) (standard if no details are given).

Technical details:

Main jet = 350
Idle jet = 20
Nozzle needle = 6EN11-53-3

Outer diameter front = 40mm
Outer diameter rear = 62mm
Total length = 74mm

Important notes:
Other intake manifolds are required! No plug & play!

Conversion must be approved by the TÜV

Suitable for:
All two-stroke vehicles where it fits or can be made to fit! :)

Mikuni carburettor TM30-6

The carburettors are often used for a conversion of the Yamaha Banshee or RD350. They fit tightly into the original intake rubber.

The carburettors have an additional Powerjet jet so that the mixture can be adjusted even better.

The offer includes:
2x carburettor TM30-6
(jetting of your choice (standard jetting if not specified))

Technical data:
Hauptdüse = 195
Leerlaufdüse = 40
Düsennadel = 5EL68-3
Power Jet Düse = 80

Notes:
To make the carburettor fit more snugly, we recommend fitting a spacer between the diaphragm and cylinder. Otherwise it will be a little tight on the engine housing.

Conversion must be approved by the TÜV

Optional oil connection:
Also available with oil connection! (The carburettors then have an oil connection with integrated non-return valve)

Suitable for:
Yamaha Banshee
Yamaha RD 350 31k, YPVS, 1WW, 1WX, 4L0, 4L1 etc.

Mikuni carburettor TM38-157

The carburettors are often used for a conversion of the Yamaha Banshee or RD350.

The carburettors have an additional Powerjet jet so that the mixture can be adjusted even better.

The offer includes:
2x carburettor TM38-157
(jetting of your choice (standard jetting if not specified))

Technical details:

Main jet = 410
Idle jet = 20
Jet needle = 6EJ12-56-3
Power Jet nozzle = 50

Outer diameter front = 44mm
Outer diameter rear = 62mm
Total length = 76mm

Important notes:
Other intake manifolds are required! No plug & play!

Conversion must be approved by the TÜV

Suitable for:
Yamaha Banshee
Yamaha RD 350 31k, YPVS, 1WW, 1WX, 4L0, 4L1 etc.

Carburettor synchronisation tester Flow Meter Synchrometer Synchronisation aid Volume flow measurement

This tool helps you to synchronise your carburettor without any problems, i.e. to adjust it evenly. Which can otherwise be a real pain. An indispensable companion for your Banshee or RD 350!

Includes:
1x synchronisation tester

Info:
The synchronisation tester should always be used when you have worked on the carburettors, throttle cables or in the area of the throttle cables to ensure that the carburettors are running in sync.
Cleanly synchronised carburettors are the be-all and end-all for these engines. Poorly adjusted carburettors mean loss of power and, in the worst case, engine damage!

Suitable for:
Yamaha Banshee all years of construction
Yamaha RD all years and models

Can of course also be used for other vehicles!

Swingarm pin complete repair kit All Balls 28-1028 Yamaha Banshee

Includes:
1x sleeve
2x dust cap
2x needle bearing
2x disc

Info:
Repair kit for the swingarm if it is worn out or the bearings are simply defective.

Suitable for:
Yamaha Banshee (all)