Silicone hose connector reduction connection air filter box e.g. f. Mikuni TM30 carburettor (51/62mm)

Mikuni carburettor TM35-1

The carburettors are often used for a conversion of the Yamaha Banshee or RD350.

The offer includes:
2x carburettor TM35-1
(jetting and needle of your choice (standard jetting if not specified))

The offer also includes:
Jetting of your choice (standard jetting if no details are given)
A different nozzle needle (if required) (standard if no details are provided.

Normally, the nozzles and the nozzle needle are replaced. All we need is your setup. Simply contact us or make a note during the ordering process.

Mikuni carburettor TM30-6

The carburettors are often used for a conversion of the Yamaha Banshee or RD350. They fit tightly into the original intake rubber.

The carburettors have an additional Powerjet jet so that the mixture can be adjusted even better.

The offer includes:
2x carburettor TM30-6
(jetting of your choice (standard jetting if not specified))

Technical data:
Main Jet = 195
Idle Jet = 40
Needle = 5EL68-3
Power Jet = 80

Notes:
To make the carburettor fit more snugly, we recommend fitting a spacer between the diaphragm and cylinder. Otherwise it will be a little tight on the engine housing.

Conversion must be approved by the TÜV

Optional oil connection:
Also available with oil connection! (The carburettors then have an oil connection with integrated non-return valve)

Suitable for:
Yamaha Banshee
Yamaha RD 350 31k, YPVS, 1WW, 1WX, 4L0, 4L1 etc.

MADE IN GERMANY

PR intake manifolds for the Yamaha Banshee or RD 350 for use with Mikuni TM35-1 carburetors


The offer includes:
2x intake manifolds incl. Mikuni flange rubber
8x screws incl. washers

Optional:
2x gasket diaphragm inlet standard
2x gasket diaphragm inlet for V-Force 4

Carburettor synchronisation tester Flow Meter Synchrometer Synchronisation aid Volume flow measurement

This tool helps you to synchronise your carburettor without any problems, i.e. to adjust it evenly. Which can otherwise be a real pain. An indispensable companion for your Banshee or RD 350!

Includes:
1x synchronisation tester

Info:
The synchronisation tester should always be used when you have worked on the carburettors, throttle cables or in the area of the throttle cables to ensure that the carburettors are running in sync.
Cleanly synchronised carburettors are the be-all and end-all for these engines. Poorly adjusted carburettors mean loss of power and, in the worst case, engine damage!

Suitable for:
Yamaha Banshee all years of construction
Yamaha RD all years and models

Can of course also be used for other vehicles!

Mikuni carburettor TM30-6

The carburettors are often used for a conversion of the Yamaha Banshee or RD350. They fit tightly into the original intake rubber.

The carburettors have an additional Powerjet jet so that the mixture can be adjusted even better.

The offer includes:
2x carburettor TM30-6
(jetting of your choice (standard jetting if not specified))

Technical data:
Main Jet = 195
Idle Jet = 40
Needle = 5EL68-3
Power Jet = 80

Notes:
To make the carburettor fit more snugly, we recommend fitting a spacer between the diaphragm and cylinder. Otherwise it will be a little tight on the engine housing.

Conversion must be approved by the TÜV

Optional oil connection:
Also available with oil connection! (The carburettors then have an oil connection with integrated non-return valve)

Suitable for:
Yamaha Banshee
Yamaha RD 350 31k, YPVS, 1WW, 1WX, 4L0, 4L1 etc.

Seal for the diaphragm inlet 3GG-13621-00-00

Suitable for Yamaha Banshee and RD 350 diaphragms
Suitable for V-Force diaphragms

Not an original part!

Oil drain plug with magnet

Includes:

1x oil drain plug M14x1,5
1x seal

Info:

Holds metal abrasion so that it does not continue to travel in the engine.

Suitable for all model years

Image similar

Water pump cover gasket Yamaha Banshee / RD 350 - 3GG-12428-01-00 / 4L0-12428-00-00

Not an original part. Seal from the accessories

Suitable for:
Yamaha Banshee (all)
Yamaha RD 350 LC, 31K, YPVS, 1WW, 1WX, 4L0, 4L1